Complete Yocto mirror with license table for TQMa6UL (2038-compliance)

- 264 license table entries with exact download URLs (224/264 resolved)
- Complete sources/ directory with all BitBake recipes
- Build configuration: tqma6ul-multi-mba6ulx, spaetzle (musl)
- Full traceability for Softwarefreigabeantrag
- GCC 13.4.0, Linux 6.6.102, U-Boot 2023.04, musl 1.2.4
- License distribution: GPL-2.0 (24), MIT (23), GPL-2.0+ (18), BSD-3 (16)

sources/meta-arm/meta-arm-bsp/documentation/n1sdp.md

@@ -0,0 +1,78 @@
+# N1SDP Development Platform Support in meta-arm-bsp
+
+## Overview
+The N1SDP provides access to the Arm Neoverse N1 SoC. The N1SDP enables software development for key enterprise technology
+and general Arm software development. The N1SDP consists of the N1 board containing the N1 SoC.
+The N1 SoC contains two dual-core Arm Neoverse N1 processor clusters.
+
+The system demonstrates Arm technology in the context of Cache-Coherent Interconnect for Accelerators (CCIX) protocol by:
+
+- Running coherent traffic between the N1 SoC and an accelerator card.
+- Coherent communication between two N1 SoCs.
+- Enabling development of CCIX-enabled FPGA accelerators.
+
+Further information on N1SDP can be found at
+https://community.arm.com/developer/tools-software/oss-platforms/w/docs/458/neoverse-n1-sdp
+
+## Configuration:
+In the local.conf file, MACHINE should be set as follow:
+MACHINE ?= "n1sdp"
+
+## Building
+```bash$ bitbake core-image-minimal```
+
+## Running
+
+# Update Firmware on SD card:
+
+(*) To use n1sdp board in single chip mode, flash:
+    n1sdp-board-firmware_primary.tar.gz firmware.
+
+(*) To use n1sdp board in multi chip mode, flash:
+    n1sdp-board-firmware_primary.tar.gz firmware to primary board,
+    n1sdp-board-firmware_secondary.tar.gz firmware to secondary board.
+
+The SD card content is generated during the build here:
+  tmp/deploy/images/n1sdp/n1sdp-board-firmware_primary.tar.gz
+  tmp/deploy/images/n1sdp/n1sdp-board-firmware_secondary.tar.gz
+
+
+Its content must be written on the N1SDP firmware SD card.
+To do this:
+- insert the sdcard of the N1SDP in an SD card reader and mount it:
+```bash$ sudo mount /dev/sdx1 /mnt```
+(replace sdx by the device of the SD card)
+
+- erase its content and put the new one:
+```bash$ sudo rm -rf /mnt/*```
+```bash$ sudo tar --no-same-owner -xzf tmp/deploy/images/n1sdp/n1sdp-board-firmware_primary.tar.gz -C /mnt/```
+```bash$ sudo umount /mnt```
+
+- reinsert the SD card in the N1SDP board
+
+Firmware tarball contains iofpga configuration files, scp and uefi binaries.
+
+**NOTE**:
+If the N1SDP board was manufactured after November 2019 (Serial Number greater
+than 36253xxx), a different PMIC firmware image must be used to prevent
+potential damage to the board. More details can be found in [1].
+The `MB/HBI0316A/io_v123f.txt` file located in the microSD needs to be updated.
+To update it, set the PMIC image (300k_8c2.bin) to be used in the newer models
+by running the following commands on your host PC:
+
+    $ sudo umount /dev/sdx1
+    $ sudo mount /dev/sdx1 /mnt
+    $ sudo sed -i '/^MBPMIC: pms_0V85.bin/s/^/;/g' /mnt/MB/HBI0316A/io_v123f.txt
+    $ sudo sed -i '/^;MBPMIC: 300k_8c2.bin/s/^;//g' /mnt/MB/HBI0316A/io_v123f.txt
+    $ sudo umount /mnt
+
+# Prepare an USB hard drive:
+
+Grub boot partition is placed on first partition of the *.wic image,
+Linux root file system is placed on the second partition of the *.wic image:
+  tmp/deploy/images/n1sdp/core-image-minimal-n1sdp.wic
+
+This *.wic image should be copied to USB stick with simple dd call.
+
+
+[1]: https://community.arm.com/developer/tools-software/oss-platforms/w/docs/604/notice-potential-damage-to-n1sdp-boards-if-using-latest-firmware-release